Twin Compressor

1.Famous compression element ensures the high performance and large air delivery.

2.Powerful engine helps to improve the reliability and reduce the fuel consumption.

3.High efficiency and energy saving filters ensure longer working life and save the maintenance cost.

4.Damped chassis and wear resistant type.

How does the variable frequency air compressor save electricity?

1. Because the pressure of the twin compressor is stable, it can be reduced to no pressure fluctuation difference, so that the air compressor system runs at a lower pressure that meets the production requirements, and the air compressor reduces the power loss caused by the upward pressure fluctuation. .

2. The general twin compressor cannot rule out the possibility of running for a long time under full load, so the capacity of the motor can only be determined according to the large demand, so the planned capacity is generally too large. In actual operation, the share of the moment of no-load operation is very high. The frequency conversion air compressor adopts frequency conversion speed regulation, which can greatly improve the operating efficiency during operation. Therefore, the potential for energy saving is great.

3. When the demand is small, the rotation speed of the motor can be reduced, and the running power of the motor can be reduced, and then further energy saving can be achieved.

How to maintain the motor of the screw air compressor

We all know that the working efficiency of the screw air compressor is closely related to the motor part. A good motor can effectively help the air compressor to reduce the failure rate and achieve more efficient power saving. But did you know? Even high-efficiency screw air compressor motors require proper maintenance.

The maintenance of the screw air compressor motor is generally mainly carried out for the bearing, which depends on the appropriate addition of lubricating oil, and the specific time node needs to be carried out according to the experience device, and the professional grease gun is used when the operation is roughly 1,800 hours. During operation, it is necessary to remove all the grease bound to the drain pipe, and then add grease. Observe the state of the grease until the previous grease is completely drained. The whole process can be said to be complete.

It is worth noting that after the addition is completed, the temperature of the bearing should preferably not exceed 120°C. Then restore the scene. The specific amount to be added depends on the temperature of the motor bearing after filling. If the temperature of the motor bearing is still below 70 degrees after the grease is added, then it can be added. This is basically the case for the motor maintenance of the screw air compressor. Tuotian air compressors are kindly reminded that after the screw air compressor motor fails, the first thing to check is the source of the failure, whether it is due to improper system protection or overload operation, etc And so on.

1. What are the ways to maintain the twin compressor?

The daily use environment of the screw air compressor motor should be kept in a dry environment, and the surface should be kept clean from time to time, and the air inlet should not accumulate dust, fibers and other debris. When the thermal protection and short circuit protection of the motor continue to operate, it should be checked whether the fault comes from the motor or the overload, or the protection device is set too low, and the fault can be put into operation after the fault is cleared.

The motor bearing should be refilled with grease when running for 1500~2000h, and the bearing temperature should not exceed 120℃. When the temperature is lower than 70℃, the interval of refilling grease can be appropriately extended. When filling oil, use a grease gun, first remove the grease plug on the oil drain pipe, add new grease until the original grease is discharged from the oil drain hole, wipe it with a rag, and tighten the oil plug after the oil is filled.

2. Record the daily maintenance and operation records of the screw air compressor

The daily maintenance and overhaul records of screw air compressors can be recorded regularly or irregularly, or recorded after maintenance. Accurate records are conducive to timely analysis and troubleshooting when the air compressor fails. The main contents of the maintenance record include inspection, cleaning, adjustment, supplementation, replacement and corresponding time.

Third, the significance of the maintenance of the screw air compressor?

Only when the screw air compressor is adequately maintained will it be in the best working condition. Proper maintenance can increase the service life of the entire machine and greatly reduce the downtime of the machine. The maintenance cycle of the screw air compressor is provided by the manufacturers with reference time. If the air compressor is installed in a clean and low temperature environment, The service period can be appropriately extended, and the correct service period should be formulated according to the use environment of the air compressor.

Hot Tags: twin compressor, China, manufacturers, suppliers, factory, customized, wholesale, in stock, Energy Saving Screw Air Compressor, Direct Driving Screw Air Compressor, VFD Three phase Motor Compressor, Variable Frequency Screw Air Compressor 8bar, Variable Frequency Direct Driven Screw Compressor, Frequency Air Compressor