Best Air Compressor Company

1. Air pressure stability

2. Variable flow control

3. No effect at startup

4. Low noise

5. The AC power supply has good voltage adaptability

There are two ways to return oil to the compressor: one is to return the oil from the oil separator, and the other is to return the oil from the air return pipe.

The oil separator is installed on the compressor exhaust pipe. Generally, 50-95% of the oil can be separated. The oil return effect is good, the speed is fast, and the amount of oil entering the system pipeline is greatly reduced, thus effectively extending the operation without oil return. time.

It’s not uncommon for cold storage refrigeration systems with extremely long pipelines, full-liquid ice-making systems, and freeze-drying equipment with very low temperatures to return more than ten minutes or even dozens of minutes after starting up, or with very little oil return. Design A bad system will cause the compressor to stop due to low oil pressure. The installation of a high-efficiency oil separator in this refrigeration system can greatly extend the operating time of the compressor without oil return, so that the compressor can safely pass the crisis stage of no oil return after starting up. best air compressor company

The lubricating oil that has not been separated will enter the system and flow with the refrigerant in the pipe to form an oil circulation. The lubricating oil enters the evaporator.

On the one hand, due to low temperature and low solubility, part of the lubricating oil is separated from the refrigerant; on the other hand, with low temperature and high viscosity, the separated lubricating oil is easy to adhere to the inner wall of the pipe and it is difficult to flow. The lower the evaporation temperature, the more difficult it is to return the oil. This requires that the design and construction of the evaporation pipeline and the return pipeline must be conducive to oil return. The common practice is to adopt a descending pipeline design and ensure a larger air flow velocity.

In practical applications, oil return problems caused by improper design of the evaporator and return line are not uncommon. For R22 and R404A systems, the oil return of the flooded evaporator is relatively difficult, and the oil return pipeline design of the system must be very careful. For such a system, the use of high-efficiency oil can greatly reduce the amount of oil entering the system pipeline, and effectively extend the non-return time of the air return pipe after the start-up. best air compressor company

When the compressor is higher than the evaporator, the oil return bend on the vertical return pipe is necessary. The return bend should be as compact as possible to reduce oil storage. The spacing between the oil return bends should be appropriate. When the number of oil return bends is large, some lubricant should be added.

The oil return line of the variable load system must also be careful. When the load is reduced, the air return speed will decrease, too low speed is not conducive to oil return. In order to ensure the oil return under low load, the vertical suction pipe can adopt double vertical pipes.

Frequent starting of the compressor is not conducive to oil return. Since the compressor stops for a short continuous operation time, there is no time to form a stable high-speed air flow in the return pipe, and the lubricating oil can only stay in the pipe. If the oil return is less than Ben oil, the compressor will be short of oil. The shorter the operating time, the longer the pipeline and the more complex the system, the more prominent the oil return problem. best air compressor company

During defrosting, the temperature of the evaporator increases and the viscosity of the lubricating oil decreases, making it easy to flow. After the defrost cycle, the refrigerant flow rate is large, and the retained lubricating oil will return to the compressor in a concentrated manner. Therefore, the frequency of the defrost cycle and the duration of each time must also be carefully set to avoid large fluctuations in the oil level or even oil shock. When the refrigerant leaks too much, the air return speed will decrease. If the speed is too low, the lubricating oil will stay in the air return line and cannot return to the compressor quickly. The start-up with liquid caused by refrigerant migration can also cause difficulty in internal oil return, but it usually takes a short time, up to ten minutes. best air compressor company

Hot Tags: best air compressor company, China, manufacturers, suppliers, factory, customized, wholesale, in stock, Direct Driving Screw Air Compressor, VFD Three phase Motor Compressor, Variable Frequency Screw Air Compressor 8bar, Energy Saving Screw Air Compressor, Variable Frequency Direct Driven Screw Compressor, Variable Frequency Screw Air Compressor